www.cncmasterkit.ru

Код: Выделить всё

;
; G - Code configuration file - with Arc Support
; for EMC2
;
DESCRIPTION = "EMC2 postprocessor(mm, arc) (*.ngc)"
;
FILE_EXTENSION = "ngc"
;
UNITS = MM
;
; Cariage return - line feed at end of each line
;
END_OF_LINE = "[13][10]"
;
; Block numbering
;
LINE_NUM_START   = 0
LINE_NUM_INCREMENT = 10
LINE_NUM_MAXIMUM   = 999999
;
; Set up default formating for variables
;
; Line numbering
FORMAT = [N|@|N|1.0]
; Spindle Speed
FORMAT = [S|@|S|1.0]
; Feed Rate
FORMAT = [F|#|F|1.1]
; Tool moves in x,y and z
FORMAT = [X|#|X|1.3]
FORMAT = [Y|#|Y|1.3]
FORMAT = [Z|#|Z|1.3]
; Arc Centre Cordinates
FORMAT = [I|@|I|1.3]
FORMAT = [J|@|J|1.3]
; Home tool positions
FORMAT = [XH|@|X|1.3]
FORMAT = [YH|@|Y|1.3]
FORMAT = [ZH|@|Z|1.3]
;
; Set up program header
;
START = "G21 G90"
START = "M03 [S]"
START = "G00 [ZH]"
START = "G00 [XH] [YH]"
;
; Program moves
;
RAPID_RATE_MOVE         = "[N] G00 [X] [Y] [Z]"
;
FIRST_FEED_RATE_MOVE   = "[N] G01 [X] [Y] [Z] [F]"
FEED_RATE_MOVE           = "[N] G01 [X] [Y] [Z] [F]"
;
FIRST_CW_ARC_MOVE         = "[N] G02 [X] [Y] [I] [J] [F]"
CW_ARC_MOVE                     = "[N] G02 [X] [Y] [I] [J] [F]"
;
FIRST_CCW_ARC_MOVE       = "[N] G03 [X] [Y] [I] [J] [F]"
CCW_ARC_MOVE               = "[N] G03 [X] [Y] [I] [J] [F]"
;
; End of file
;

Код: Выделить всё

;
; G - Code configuration file - with Arc Support
; for EMC2
;
DESCRIPTION = "EMC2 postprocessor(mm, arc) (*.ngc)"
;
FILE_EXTENSION = "ngc"
;
UNITS = MM
;
; Cariage return - line feed at end of each line
;
END_OF_LINE = "[13][10]"
;
; Block numbering
;
LINE_NUM_START   = 0
LINE_NUM_INCREMENT = 10
LINE_NUM_MAXIMUM   = 999999
;
; Set up default formating for variables
;
; Line numbering
FORMAT = [N|@|N|1.0]
; Spindle Speed
FORMAT = [S|@|S|1.0]
; Feed Rate
FORMAT = [F|#|F|1.1]
; Tool moves in x,y and z
FORMAT = [X|#|X|1.3]
FORMAT = [Y|#|Y|1.3]
FORMAT = [Z|#|Z|1.3]
; Arc Centre Cordinates
FORMAT = [I|@|I|1.3]
FORMAT = [J|@|J|1.3]
; Home tool positions
FORMAT = [XH|@|X|1.3]
FORMAT = [YH|@|Y|1.3]
FORMAT = [ZH|@|Z|1.3]
;
; Set up program header
;
START = "G21 G90"
START = "M03 [S]"
START = "G04 P5"
START = "G00 [ZH]"
START = "G00 [XH] [YH]"
;
; Program moves
;
RAPID_RATE_MOVE         = "[N] G00 [X] [Y] [Z]"
;
FIRST_FEED_RATE_MOVE   = "[N] G01 [X] [Y] [Z] [F]"
FEED_RATE_MOVE           = "[N] G01 [X] [Y] [Z] [F]"
;
FIRST_CW_ARC_MOVE         = "[N] G02 [X] [Y] [I] [J] [F]"
CW_ARC_MOVE                     = "[N] G02 [X] [Y] [I] [J] [F]"
;
FIRST_CCW_ARC_MOVE       = "[N] G03 [X] [Y] [I] [J] [F]"
CCW_ARC_MOVE               = "[N] G03 [X] [Y] [I] [J] [F]"
;
; End of file
;